IPB


Welcome Guest ( Log In | Register )

 
Reply to this topicStart new topic
Vfd Regen Mode
Digg this topic · Save to del.icio.us · Slashdot It · Post to Technorati · Post to Furl · Submit to Reddit · Share on Facebook · Fark It · Googlize This Post · Add to ma.gnolia · Tag to Wink · Add to MyWeb · Add to Netscape
rahuljadhav1
post Nov 29 2007, 11:46 AM
Post #1


Intermediate Member
***

Group: Full Member
Posts: 21
Joined: 11-September 07
From: Noida
Member No.: 3,766




Dear all

I want information about VFD in regenerative mode.So what are all general points that

i have to take care,all calculations for regenerative application?

Regards

Rahul
Go to the top of the page
 
+Quote Post
marke
post Nov 30 2007, 06:54 AM
Post #2


Posting Freak
******

Group: Moderator
Posts: 2,115
Joined: 24-April 02
From: Christchurch, New Zealand
Member No.: 1



Hello Rahul

This is a rather open ended question!

If you can be more specific, we can give you a better answer.
As a brief overview, I assume that you are referring to an AC drive, there are two major types of regenerative operation.
  1. Brake Resistor
  2. Active front end

When you decelerate a load, you are removing kinetic energy from that load. If you decelerate slowly, the kinetic energy can be dissipated in the load as the motor slows down. As you increase the rate of deceleration, the energy removed from the load becomes too high to dissipate in the load, so the energy is transfered back into the drive. This causes the DC bus voltage to rise. If the energy transfer into the drive was unchecked and not dissipated elsewhere, the voltage would get high enough to cause damage to the drive.
One option, is to add a chopper transistor and a dump resistor. If the voltage rises above a threshold voltage, the chopper transistor turns on and dumps energy into the brake resistor. This will prevent the DC bus voltage from rising too high provided that the resistance is low enough to draw energy out of the drive faster than it is taken from the load.
Another option is to use an active front end where the input rectifier is actually and inverter stage that is able to chop up the DC voltage and feed it back into the supply. During braking, the load is treated as the supply and the mains supply is treated as a load. The active front end drive is a drive that can transfer energy in either direction.

Best regards,


--------------------
Go to the top of the page
 
+Quote Post
rahuljadhav1
post Dec 3 2007, 11:20 AM
Post #3


Intermediate Member
***

Group: Full Member
Posts: 21
Joined: 11-September 07
From: Noida
Member No.: 3,766



Dear sir

The information i needed was more that what you have given.

But thank you very much for the same.Well I have got little more on it from

some others.

This is a great forum you are running.Keep doing the good work

Regards

Rahul
Go to the top of the page
 
+Quote Post
marke
post Dec 3 2007, 06:13 PM
Post #4


Posting Freak
******

Group: Moderator
Posts: 2,115
Joined: 24-April 02
From: Christchurch, New Zealand
Member No.: 1



Hello Rahul

Thank you for your comments.

The difficulty with open ended questions is that it is possible to write a book as an answer and still not cover the information wanted.
As this is a free information service, there is limited time available and so we don't write books as replies.
If you are more specific with your question, the answer can be more specific. - It makes things much easier for us and more helpful for you.

Best regards,


--------------------
Go to the top of the page
 
+Quote Post

Reply to this topicStart new topic
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:

 



Collapse

> Similar Topics

    Topic Title Replies Topic Starter Views Last Action
No New Posts   1 eldhobaby 570 13th March 2005 - 04:11 AM
Last post by: marke
No New Posts   7 Carl 663 24th August 2005 - 10:59 AM
Last post by: Carl
No New Posts   10 jraef 1,091 27th September 2006 - 11:18 AM
Last post by: joze
No New Posts   4 barani 1,798 24th December 2006 - 05:12 PM
Last post by: barani
No New Posts   6 Matt303 1,543 5th October 2007 - 01:18 PM
Last post by: Matt303



RSS Lo-Fi Version Time is now: 7th January 2009 - 10:30 PM
hosted by : L M Photonics Ltd